At a glance data:
Minimum Rating:
624.0BHP
Maximum Rating:
803.0BHP
Aspiration:
TA, TTA
Bore:
5.7in
Overview
C18 ACERT auxiliary/generator set engines incorporate a separate circuit aftercooling system (SCAC) for all configurations. The primary advantage of the SCAC systsem is reduced aftercooler corrosion since no sea water circulates through the aftercooler. Many other improvements on these engines also contribute to minimizing owning and operating costs. The EPA Tier 3, IMO II, EU Stage IIIA compliant ratings are available with heat exchanger or keel cooled options. All major MCS type approvals are available from the factory.
Power Rating
Minimum Rating:
624.0BHP
Maximum Rating:
803.0BHP
Engine Specifications
Aspiration:
TA, TTA
Bore:
5.7in
Displacement:
1106.0in³
Configuration:
In-Line 6, 4-Stroke-Cycle Diesel
Stroke:
7.2in
Rotation from Flywheel End:
Counterclockwise
Dimensions & Weights
Length:
73.0in
Height:
51.2in
Dry Weight:
1950.0lb
Width:
44.6in
Standard Equipment
air inlet system
- Separate circuit after-cooled (SCAC)
- Open Crankcase Ventilation (OCV) system
- Turbocharger, jacket water cooled
- Turbocharger inlet, 152 mm (6 in) OD straight connection
control system
- Programmable low idle
- Electronic diagnostics and fault logging
- Electronic fuel/air ratio control
- Engine Protection Mode for extended ambient conditions - EPA Tier 3 Ratings Only
- 70-pin customer connector
- Three types of throttle inputs (primary/ secondary PWM, 0-5V, 4-20mA
cooling system
- Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
- Engine JW and SCAC Shell & Tube Heat Exchangers for HEX cooled engines
- SCAC pump, gear driven, for HEX cooled engines only
- Jacket water pump, gear driven
- Auxiliary water pump, gear driven
- Sea water pump, bronze impeller, gear driven
- SCAC and JW shunt tanks for maintaining proper pump inlet pressures
exhaust system
- 152 mm (6 in) round flanged outlet
- Water-cooled exhaust manifold & turbocharger
flywheels & flywheel housings
- Flywheel Housing, SAE No. 0
- Flywheel, 18 inch, 136 teeth
- SAE standard rotation
fuel system
- Front service simplex fuel system
- Fuel transfer pump, gear driven
- Manual fuel priming pump
- Hybrid fuel line design
lube system
- Front service simplex oil system
- Center sump oil pan:
- Front and top service oil filler locations
- Front service dipstick
- Oil pump, gear driven
mounting system
- Front support - adjustable
power take-offs
- Hydraulic Pump Drive
- Crankshaft Pulleys
- Front Stub Shaft
- Front Enclosed Clutch
general
- Front damper guard
- Front service engine
- Common electrical bonding point
- Engine does not ship with zinc components
- NOTE: These engines are for constant speed generator set applications only, and NOT to be used for variable speed applications
Optional Equipment
exhaust system
- Dry Elbows
- Water-Cooled Elbows
- Flexible Fitting
- Flange
- Muffler
- Muffler Spark Arresting
air inlet system
- Air Inlet Adapter
charging system
- Battery Chargers
- Charging Alternators
- Alternator Mounting Group
- Ammeter
control system
- MECP I - Marine Engine Control Panel
- Caterpillar Alarm and Protection
- Load Sharing Attachment
cooling system
- Aux Expansion Flange Kit
fuel system
- Duplex Fuel Filters
- Fuel Cooler
- Primary Fuel Filters
- Flexible Fuel Lines
instrumentation
- Instrument Panels
- OEM Wiring Harness
- Gauges
- Oil Level Sensor
lube system
- Duplex Oil Filters
- Sump Pump
power take-offs
- Crankshaft Pulleys
- Front Stub Shaft
- Hydraulic Pump Drive Adapter
- Front Enclosed Clutch
protection system
- Marine Classification Society and SOLAS
starting system
- Electric Starting Motors - Single 24 Volt
- Air Starting Motor
- Air Start Accessories
- Starting Aids - JW Heaters
- Battery Sets - 24 Volt - Dry
mounting system
- Front Support
- REAR ENGINE SUPPORT
packing
- Engine Protective Cover
- Storage Preservation
- Export Packing
Similar Products
3516E Marine Auxiliary Engine (U.S. EPA Tier 4 Final)
Minimum Rating:
624.0BHP
Maximum Rating:
803.0BHP
Aspiration:
TA, TTA
Bore:
5.7in
Cat C18 Auxiliary/Generator Set Engine (EPA Tier 3)
Minimum Rating:
624.0BHP
Maximum Rating:
803.0BHP
Aspiration:
TA, TTA
Bore:
5.7in
Cat C32 Auxiliary / Diesel Electric Propulsion (US EPA Tier 3 / IMO II)
Minimum Rating:
624.0BHP
Maximum Rating:
803.0BHP
Aspiration:
TA, TTA
Bore:
5.7in