At a glance data:
Minimum Rating:
791.0BHP
Maximum Rating:
1333.0BHP
Aspiration:
TTA
Displacement:
1959.0in³
Overview
C32 ACERT auxiliary/generator set engines incorporate a separate circuit aftercooling system (SCAC) for all configurations. The primary advantage of the SCAC systsem is reduced aftercooler corrosion since no sea water circulates through the aftercooler. Many other improvements on these engines also contribute to minimizing owning and operating costs. The IMO II compliant ratings are available with heat exchanger or keel cooled options. Heat exchanger configurations have an optional front mounted sea water pump.
Power Rating
Minimum Rating:
791.0BHP
Maximum Rating:
1333.0BHP
Engine Specifications
Aspiration:
TTA
Displacement:
1959.0in³
Rotation from Flywheel End:
Counterclockwise
Stroke:
6.4in
Bore:
5.7in
Configuration:
Vee 12, 4-Stroke-Cycle Diesel
Dimensions & Weights
Minimum Dry Weight:
6950.0lb
Minimum Length:
83.5in
Minimum Height:
60.9in
Maximum Length:
89.9in
Maximum Dry Weight:
7160.0lb
Maximum Height:
62.5in
Width:
60.2in
Standard Equipment
air inlet system
- Separate circuit after-cooled (SCAC)
- Air cleaner
- Turbocharger, jacket water cooled
- Turbocharger inlet, 152 mm (6 in) OD straight connection
control system
- Programmable Low Idle (550 - 750 rpm)
- Programmable High Idle Limit for WOSR Ratings
- Electronic diagnostics and fault logging
- Engine and transmission monitoring (speed, temperature, pressure)
- Electronic fuel/air ratio control
- Engine Protection Mode for extended ambient conditions
- 70-pin customer connector
- Throttle Input signal options
- 0 - 5 Volts
- 4 - 20 mA
- PWM (Pulse Width Modulated)
cooling system
- Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
- Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines
- SCAC pump, gear driven
- Jacket water pump, gear driven
- Sea water pump, bronze impeller, gear driven, when selected for Hex cooled engines
- Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection
- Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt
- SCAC and JW shunt tanks for maintaining proper pump inlet pressures
exhaust system
- Water-cooled exhaust manifold & turbocharger
- 4 Bolt 130 mm (5.12 in) diameter flanged outlet
flywheels & flywheel housings
- SAE standard rotation (CCW facing exciter end)
- Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth
fuel system
- Duplex Fuel Filters, Spin-on, RH & LH service
- Fuel connections size: r driven
- Plate-type fuel cooler installed behind Aftercooler Shunt Tank
- Fuel transfer pump, gear driven
- Manual fuel priming pump
- Hybrid fuel line design
lube system
- Simplex Oil Filters, RH or LH service
- Deep sump oil pan
- RH or LH service oil filler locations
- RH or LH service dipstick
- Oil pump, gear driven
mounting system
- Front support - 33 inches wide
power take-offs
- Front Poly-V groove pulley (Quantity 1) for auxiliary drives
general
- Common electrical bonding point
- Engine does not ship with zinc components
Optional Equipment
exhaust system
- Dry Elbows
- Flexible Fitting
- Flange
- Muffler
- Muffler Spark Arresting
air inlet system
- Air Inlet Adapter
charging system
- Battery Chargers
- Charging Alternators
- Ammeter
control system
- Load Sharing Attachment
- Instrument Panels
- Caterpillar Alarm Protection
- Fuel and Oil Shielding
fuel system
- Water Separator
general
- Fumes Disposal System
instrumentation
- Instrument Panels
- OEM Wiring Harness
- Engine to Engine Harness
- Gauges
- Transmission Sensors
- Exhaust Temperature Sensors
lube system
- Duplex Oil Filters
- Sump Pump
power take-offs
- Rear Hydraulic Pump Drive
starting system
- Electric Starting Motors - Single 24 Volt
- Air Starting Motor
- Dual Starting Motors (Electric and Air)
- Air Start Accessories
- Starting Aids - JW Heaters
- Battery Sets - 24 Volt - Dry
mounting system
- Front Support
- Rear Support
- Isolators Mounts
- Adapter Kits
packing
- Engine Protective Cover
- Storage Preservation
- Export Packing
Similar Products
3516E Marine Auxiliary Engine (U.S. EPA Tier 4 Final)
Minimum Rating:
791.0BHP
Maximum Rating:
1333.0BHP
Aspiration:
TTA
Displacement:
1959.0in³
Cat C18 Auxiliary/Generator Set Engine (EPA Tier 3)
Minimum Rating:
791.0BHP
Maximum Rating:
1333.0BHP
Aspiration:
TTA
Displacement:
1959.0in³
Cat C32 Auxiliary / Diesel Electric Propulsion (US EPA Tier 3 / IMO II)
Minimum Rating:
791.0BHP
Maximum Rating:
1333.0BHP
Aspiration:
TTA
Displacement:
1959.0in³